PriceList for Hydraulic System - AC 380V 1.5KW Single Acting Hydraulic Power Packs – Oumai
PriceList for Hydraulic System - AC 380V 1.5KW Single Acting Hydraulic Power Packs – Oumai
PriceList for Hydraulic System - AC 380V 1.5KW Single Acting Hydraulic Power Packs – Oumai Detail:
Main Specifications
Motor: AC 380V 1.1KW
Solenoid valve: 2/2ways solenoid control valve
Pump displacement: 3.2CC/REV
System flow: 4.5lpm
Tank: 12L steel square tank
Mounting type: Vertical
Hydraulic power unit
| Power Voltage | AC110, AC220, AC380, DC12V, DC24V or customized |
| Moter Power | 0.75kw, 1.1kw, 1.5kw, 2.2kw, 3.0kw or customized |
| Pump Displacement | 0.45ml/r, 0.75ml/r, 1.0ml/r, 1.6ml/r, 2.0ml/r, 2.5ml/r, 3.3ml/r, 4.2ml/r,5.8 ml/r or customized |
| Solenoid Valve Voltage | DC12V, DC24V, AC24V, AC110V, AC220V, manual valve |
| Mounting Way | Horizontal, Vertical |
| Mounting position | Valve block, bracket, oil tank, electric motor |
| System Pressure | 10mpa, 16mpa, 20mpa, 25mpa |
| Capacity of tank | 1.7L, 2.8L, 3.6L, 5.0L, 6.0L, 8.0L, 10.0L, 12.0L or customized |
| Circuit | 01-20 |
| Port | 3/8″ (BSPP/NPT) or customized |
| Working | Continute working, short time working |
| Frequency | 50HZ, 60HZ |
Precautions for Use
1. Please read the operation manual carefully and check the product model and parameters for correctness.
2. The hydraulic power unit should be installed correctly and connected correctly. Pay attention to whether the voltage of motor and solenoid valve is consistent with the power supply (see electrical schematic diagram), and whether the rotation direction of motor is correct (clockwise from the end of the shaft).
3. Regular
The power unit motor is gap type
4. The work week
The continuous working time of one start is 3 minutes and the rest is 7 minutes. It can not run continuously.
5. The working pressure of the hydraulic power unit has been adjusted when it leaves the factory. In order to maintain a good use state, please do not adjust it casually.
6. The hydraulic power unit should use anti-wear hydraulic oil with a kinematic viscosity of 27 43mm/s(50°C). Ya-n46 is recommended when the oil temperature is lower than 50°C, and YA-N68 is recommended when the oil temperature is higher than 50°C
10~ 25μm filter filter, conventional adding amount is 85~90% of the effective volume of the tank, conventional oil temperature should be within the range of -10~80°C, especially cold areas, low temperature hydraulic oil should be used.
Product detail pictures:
Related Product Guide:
To create much more price for clients is our company philosophy; purchaser growing is our working chase for PriceList for Hydraulic System - AC 380V 1.5KW Single Acting Hydraulic Power Packs – Oumai , The product will supply to all over the world, such as: United States, India, Cyprus, Our solutions have national accreditation requirements for qualified, good quality products, affordable value, was welcomed by individuals all over the world. Our products will continue to improve inside the order and appear forward to cooperation with you, Definitely should any of those goods be of curiosity to you, be sure to letus know. We'll be satisfied to supply you a quotation up on receipt of the detailed needs.
By Lilith from Iceland - 2018.11.04 10:32
The company can think what our think, the urgency of urgency to act in the interests of our position, can be said this is a responsible company, we had a happy cooperation!
By Sabina from Chile - 2018.02.08 16:45
